Thingiverse
iPhone 4S Case Flowers
door Woolpit
29
Downloads
24
Likes
2
Makes
Customized version of http://www.thingiverse.com/thing:40703
Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=40703
EN:
Case turned out. But! 1. In my program can not disable the mandatory layer of the substrate and eventually detach from the back wall of the patterned substrate was problematic. 2. Case turned on with a margin of 1 mm in length and width. That is, that the phone was held tightly in the case, will have to stick to the inner walls of the seal (foam tape).
In any case, many thanks to the creators - the team Makerbot!
RU:
ÐšÐµÐ¹Ñ Ð¿Ð¾Ð»ÑƒÑ‡Ð¸Ð»ÑÑ. Ðо! 1. Ð’ моей программе Ð½ÐµÐ»ÑŒÐ·Ñ Ð¾Ñ‚ÐºÐ»ÑŽÑ‡Ð¸Ñ‚ÑŒ обÑзательный Ñлой подложки и в итоге отделÑÑ‚ÑŒ заднюю узорную Ñтенку от подложки было проблематично. 2. ÐšÐµÐ¹Ñ Ð¿Ð¾Ð»ÑƒÑ‡Ð¸Ð»ÑÑ Ð½Ð° 1 мм Ñ Ð·Ð°Ð¿Ð°Ñом по длине и ширине. Т.е. что бы телефоÐ
Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=40703
EN:
Case turned out. But! 1. In my program can not disable the mandatory layer of the substrate and eventually detach from the back wall of the patterned substrate was problematic. 2. Case turned on with a margin of 1 mm in length and width. That is, that the phone was held tightly in the case, will have to stick to the inner walls of the seal (foam tape).
In any case, many thanks to the creators - the team Makerbot!
RU:
ÐšÐµÐ¹Ñ Ð¿Ð¾Ð»ÑƒÑ‡Ð¸Ð»ÑÑ. Ðо! 1. Ð’ моей программе Ð½ÐµÐ»ÑŒÐ·Ñ Ð¾Ñ‚ÐºÐ»ÑŽÑ‡Ð¸Ñ‚ÑŒ обÑзательный Ñлой подложки и в итоге отделÑÑ‚ÑŒ заднюю узорную Ñтенку от подложки было проблематично. 2. ÐšÐµÐ¹Ñ Ð¿Ð¾Ð»ÑƒÑ‡Ð¸Ð»ÑÑ Ð½Ð° 1 мм Ñ Ð·Ð°Ð¿Ð°Ñом по длине и ширине. Т.е. что бы телефоÐ
Heb je dit model geprint? Inloggen en deel je make!
Log in om een reactie achter te laten
InloggenNog geen reacties – wees de eerste!
