Slicer Discord
汉诺塔发育玩具 益智玩具 – 3D-Druckmodell von MakerOnline MakerOnline
汉诺塔发育玩具 益智玩具 – Bild 1 汉诺塔发育玩具 益智玩具 – Bild 2 汉诺塔发育玩具 益智玩具 – Bild 3
Toys&Games / Building Toys

汉诺塔发育玩具 益智玩具

32 Downloads
17 Likes
0 Makes
Zum Modell
汉诺塔的玩法规则如下: The gameplay rules for the Tower of Hanoi are as follows: 目标:将一根柱子上的所有圆盘移动到另一根柱子上,且在整个过程中,始终遵循以下规则。 Goal: Move all disks on one pillar to another, and always follow the following rules throughout the process. 规则: Rules: 1、每次只能移动一个圆盘。 1. Only one disc can be moved at a time. 2、圆盘只能移动到另一根柱子上或从柱子上取下,不能放置在已有更大圆盘的上面,即小圆盘必须始终位于大圆盘之上。 2. The disk can only be moved to another pillar or removed from the pillar, and cannot be placed on top of an existing larger disk, that is, the small disk must always be above the large disk. 步骤(以3层汉诺塔为例): Steps (using the 3-story Tower of Hanoi as an example): 1、先将上面两个圆盘(即较小的圆盘)从起始柱移动到辅助柱上,以目标柱作为中转。 1. First, move the upper two disks (i.e. the smaller disks) from the starting column to the auxiliary column, using the target column as a transfer point. 2、然后将最大的圆盘从起始柱移动到目标柱上。 2. Then move the largest disk from the starting column to the target column. 3、最后将辅助柱上的两个圆盘移动到目标柱上,以起始柱作为中转。 3. Finally, move the two disks on the auxiliary column to the target column, using the starting column as a transfer point. 注意事项: matters needing attention: 1、在移动圆盘时,必须始终遵循上述规则,否则游戏将无法进行下去。 1. When moving the disc, the above rules must always be followed, otherwise the game will not continue. 2、汉诺塔游戏需要耐心和策略,因为随着圆盘数量的增加,所需的移动步骤也会大幅增加。 2. The Tower of Hanoi game requires patience and strategy, as the number of discs increases, the required movement steps also increase significantly. 汉诺塔是一个既有趣又富有挑战性的益智游戏,它能够锻炼玩家的逻辑思维和问题解决能力。 Tower of Hanoi is a fun and challenging puzzle game that can exercise players' logical thinking and problem-solving abilities. 如果您对模型满意,请给个免费的点赞和收藏,非常感谢! If you are satisfied with the model, please give a free like and collect, thank you very much!
Kategorie
Toys&Games / Building Toys
Quelle
MakerOnline
Veröffentlicht
Aktualisiert
Was du zum Drucken brauchst: Anfänger Niedrige Konfidenz
Einteilig
Supports 1/3
Zusammenbau 0/3
Einstellungen 1/3
Druckbett 0/3
Nachbearbeitung 0/3
Drucker
FDM / FFF
Dateiformat
STL
Material
PLA
Software
Cura, PrusaSlicer o. Ä.
Noch keine Bewertungen
Noch keine Kommentare – sei der Erste!

Ähnliche Modelle

6 Vorschläge
Feed Blog Slicer Kostenrechner Bildersuche Einreichen Kontakt Discord ☕ Buy me a coffee
DE EN FR ES IT NL

Zur Sammlung hinzufügen