Slicer Discord
TF-07海鹰号武装直升机舰载版(已分盘,无需五金) – 3D-Druckmodell von MakerOnline MakerOnline
TF-07海鹰号武装直升机舰载版(已分盘,无需五金) – Bild 1 TF-07海鹰号武装直升机舰载版(已分盘,无需五金) – Bild 2 TF-07海鹰号武装直升机舰载版(已分盘,无需五金) – Bild 3 TF-07海鹰号武装直升机舰载版(已分盘,无需五金) – Bild 4 TF-07海鹰号武装直升机舰载版(已分盘,无需五金) – Bild 5 TF-07海鹰号武装直升机舰载版(已分盘,无需五金) – Bild 6
Miniatures

TF-07海鹰号武装直升机舰载版(已分盘,无需五金)

522 Downloads
144 Likes
0 Makes
Zum Modell
这是我原创武器载具三部曲之空战系列飞机之一,代号TF-07,中文名“海鹰”。乃是平行宇宙中的一款海军专用款武装直升机,主要功能是对海进行潜艇搜索和攻击。其搭载一门4管加特林机炮,共可挂载3枚反潜鱼雷。飞机外加两个1000升的副油箱,使其拥有近1500公里的作战半径,远超陆航版,整机身采用传统后三角固定式起落架布局,方便维护。(以上是我对该飞机的性能参数设定,仅供娱乐,)。 This is one of my original weapon and vehicle trilogy air combat series aircraft, codenamed TF-07, and the Chinese name is "Sea Eagle". It is a naval-specific armed helicopter in the parallel universe, with its main function being submarine search and attack on the sea. It is equipped with a 4-bar Gatling machine cannon, which can carry 3 anti-submarine torpedoes in total. The aircraft plus two 1,000-liter secondary fuel tanks give it a combat radius of nearly 1,500 kilometers, far exceeding the Land Aviation version. The entire fuselage adopts a traditional rear triangular fixed landing gear layout for easy maintenance. (The above are my performance parameters for this aircraft, for entertainment only,). 模型尺寸:机身长184毫米,宽105毫米,高73毫米。螺旋桨整体直径为258毫米。已拆分,所有机型可打印。(螺旋桨不能自由转动The propeller is locked) Model size: The body length is 184 mm, the width is 105 mm, and the height is 73 mm. The overall diameter of the propeller is 258 mm. Split, all models can be printed. 用到的工具(tool): 镊子tweezers 尖嘴钳Point-nosed pliers 胶水glue 注意事项(Things to note): 本模型只能作为静态展示,螺旋桨不能转; This model is for static display only; the propeller cannot rotate. 模型零件较小,所有从打印机拿下来的时候请小心,避免丢失或掰断; The model parts are small, please be careful when you take them off from the printer to avoid loss or breaking; 除了轮胎和螺旋桨不需要用胶水固定外,其余部分均使用胶水固定; Except for the tires and propellers that do not need to be fixed with glue, the rest are fixed with glue; 后起落架固定轴比较细小,安装时候请小心; The rear landing gear fixing shaft is relatively small, please be careful when installing; 打印前请清洁打印板,做好耗材烘干处理和流量校准; Please clean the printing board before printing, dry the consumables and calibrate the flow; 本模型零件较多,请按照说明书组装; This model has many parts, please assemble them according to the instructions;
Kategorie
Miniatures
Quelle
MakerOnline
Veröffentlicht
Aktualisiert
Was du zum Drucken brauchst: Mittel Niedrige Konfidenz
Warum?
Supports nötig
Einteilig Supports nötig
Supports 2/3
Zusammenbau 0/3
Einstellungen 1/3
Druckbett 0/3
Nachbearbeitung 1/3
Drucker
FDM / FFF
Dateiformat
STL
Material
PLA
Nachbearbeitung
Kleben
Software
Cura, PrusaSlicer o. Ä.
Gleicher Designer, mehr Plattformen

虾七八想 veröffentlicht auch auf

58 zusätzliche Modelle auf 2 weiteren Plattformen

Verifiziert durch übereinstimmende Modelltitel über Plattformen hinweg.
Noch keine Bewertungen
Noch keine Kommentare – sei der Erste!

Ähnliche Modelle

6 Vorschläge
Feed Blog Slicer Kostenrechner Bildersuche Einreichen Kontakt Discord ☕ Buy me a coffee
DE EN FR ES IT NL

Zur Sammlung hinzufügen