Tool
Zum Modell
Three hand
0
Downloads
0
Likes
0
Makes
This is a wire soldering clamp (a "third hand").
Length: 70 mm; Width: 40 mm.
Dimensions can be adjusted in your slicer.
Wishing everyone good health and success!
Length: 70 mm; Width: 40 mm.
Dimensions can be adjusted in your slicer.
Wishing everyone good health and success!
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
three hand
clamp
holder
soldering
wires
electrical
electronics
instrument
Kategorie
Tool
Quelle
Cults3D
Veröffentlicht
Aktualisiert
Was du zum Drucken brauchst:
Anfänger
Niedrige Konfidenz
Einteilig
Supports
1/3
Zusammenbau
0/3
Einstellungen
1/3
Druckbett
0/3
Nachbearbeitung
0/3
Drucker
FDM / FFF
Dateiformat
STL
Material
Software
Cura, PrusaSlicer o. Ä.
Hast du dieses Modell gedruckt? Einloggen und dein Make teilen!
Noch keine Bewertungen
Melde dich an, um einen Kommentar zu hinterlassen
AnmeldenNoch keine Kommentare – sei der Erste!
Ähnliche Modelle
6 VorschlägeBenchy - The jolly 3D printing torture-test
von CreativeTools
↓ 97.5k ♥ 1.7k
Print in Place- Distance Measuring Roll Tool
von SunShine
↓ 35.9k ♥ 2.5k
Most Common Metric Nut And Bolt - M2 through M20
von TheTNR
↓ 30.8k ♥ 1.7k
IMPERIAL RAPID CANNON - ULTRA MEGA PACK !
von AtlantisPrime
↓ 25.6k ♥ 2.2k
J3D Tech's Boxes of Calibration V4
von J3D-Tech
↓ 21.1k ♥ 616
Shape Snake Fidget Fun - Print in Place
von virtubob
↓ 19.8k ♥ 1.2k